Wooden door grain transfer machine
Plastic transfer film, painted wooden door manufacturing process
1, according to the specifications of the door, open the Jie density (or density) of fiber board, and then through the computer engraving or other desired pattern carved:
2, with a special pressure door door leaf pressure, until the glue is dry, Jie into compliance with the specifications of the door leaf. Door and door frame synchronous manufacturing. The door and the door frame blank after feeding after administration of ash, after grinding into the next process:
3, leaf spraying and wood grain transfer and two times to complete. For the first time, spraying water, the first door on the platform, the surface dust blown clean, and then sprayed with special plastic glue, and ensure the front and side doors are uniform glue, if you need to do transverse effect, can be in place on the shop to do horizontal transfer film cutting Jie good, etc. after the glue dry the door on the plastic machine platform, covered with wood grain transfer film, the temperature of -140 DEG C to 120 plastic machine, plastic machine put pressure to second 7kg-8kd blister, glue and plastic, process can be repeated for the first time. In addition, the spray and plastic door door only by a single program to complete the program:
4, after the completion of the blister, the wood grain transfer film tear off, and check whether the wood film is complete suction in place, if there is a defect, to repair intact, and then transferred to the next process:
5, the last process is painting and grinding: before painting, first use air guns to clean the door leaf and door frame, especially the groove position of the door leaf, so as not to affect the paint finish. PU primers are recommended for door leaf and door frame primers. When the primer is dry, then go into the grinding process. After the grinding is finished, the surface oil is modified (sprayed paint), and finally sprayed with paint to dry:
A special process with 6, line, our company can provide support, manufacturers only need to make simple line surface after cleaning, paint can be sprayed on.
1, according to the specifications of the door, open the Jie density (or density) of fiber board, and then through the computer engraving or other desired pattern carved:
2, with a special pressure door door leaf pressure, until the glue is dry, Jie into compliance with the specifications of the door leaf. Door and door frame synchronous manufacturing. The door and the door frame blank after feeding after administration of ash, after grinding into the next process:
3, leaf spraying and wood grain transfer and two times to complete. For the first time, spraying water, the first door on the platform, the surface dust blown clean, and then sprayed with special plastic glue, and ensure the front and side doors are uniform glue, if you need to do transverse effect, can be in place on the shop to do horizontal transfer film cutting Jie good, etc. after the glue dry the door on the plastic machine platform, covered with wood grain transfer film, the temperature of -140 DEG C to 120 plastic machine, plastic machine put pressure to second 7kg-8kd blister, glue and plastic, process can be repeated for the first time. In addition, the spray and plastic door door only by a single program to complete the program:
4, after the completion of the blister, the wood grain transfer film tear off, and check whether the wood film is complete suction in place, if there is a defect, to repair intact, and then transferred to the next process:
5, the last process is painting and grinding: before painting, first use air guns to clean the door leaf and door frame, especially the groove position of the door leaf, so as not to affect the paint finish. PU primers are recommended for door leaf and door frame primers. When the primer is dry, then go into the grinding process. After the grinding is finished, the surface oil is modified (sprayed paint), and finally sprayed with paint to dry:
A special process with 6, line, our company can provide support, manufacturers only need to make simple line surface after cleaning, paint can be sprayed on.
Foshan District of Shunde City Jia Shun Machinery Co. Ltd. is a company specializing in the design and manufacture of woodworking machinery, mainly engaged in the production of PUR veneer, PUR flat machine, PUR machine of wood veneer, wood veneer sheet transfer machine, machine, positive and negative pressure veneer film and other machine manufacturers. Telephone: 0757-27835567
